CNC and DNC software settings for Fagor.

These settings are for the DNC Precision software only. They may not work with other software.

Fagor 800 - Machine parameters

Set the following parameters on the PC

Serial port tab

Machine name	Fagor 800
Serial port	COM2 (or any free COM port)
Baud	4800
Data bits	7
Parity	Even
Stop bits	1

Data flow control tab

Use DTR	False
Use RTS	True
Require DSR	False
Require CTS	True
Set RTS	False
Set DTR	False
Software flowcontrol	Both
Xon char	#11
Xoff char	#13

Data exchange format tab

Format mode	Uniform
Format parameters	Program start: Program end: Line start: Line end: #0D#0A Skip lines: Ignore characters: No characters for remove Remove blank lines: No Program name prefix: O Program starting characters in the file: No Program ending characters in the file: No

Null modem cable, without handshake

PC, 9pin, DB9M | CNC, 25pin, DB25

Null modem cable, with full handshake

PC, 9pin, DB25M | CNC, 25pin, DB25

Null modem cable, without handshake

PC, 25pin, DB25M | CNC, 25pin, DB25

Null modem cable, with full handshake

PC, 25pin, DB25M | CNC, 25pin, DB25

Fagor 8010 - Machine parameters

Set the following parameters on the machine

P0 (baud rate)	7 (9600)
P1 (data bits)	1 (8 data bits)
P2 (parity)	0 (no parity)
P3 (stop bits)	0 (one stop bit)
P4 (protocol type)	0 (general device)
P5 (Fagor DNC is active)	No
P6 (Debug)	No
P7 (Abort characters)	0
P8 (EOL characters)	0 (LF)
P9 (EOT characters)	0
P10 (Xon and Xoff)	Yes

If you want you can change baud rate in the parameter P0 to:
Baud	Parameter value
1200	4
2400	5
4800	6
9600	7
19200	8
38400	9
57600	10

Set the following parameters on the PC

Serial port tab

Machine name	Fagor 8010
Serial port	COM2 (or any free COM port)
Baud	9600
Data bits	8
Parity	None
Stop bits	1

Data flow control tab

Use DTR	False
Use RTS	False
Require DSR	False
Require CTS	False
Set RTS	False
Set DTR	False
Software flowcontrol	Both
Xon char	#11
Xoff char	#13

Data exchange format tab

Format mode	Uniform
Format parameters	Program start: Program end: Line start: Line end: #0A Skip lines: Ignore characters: No characters for remove Remove blank lines: No Program name prefix: O Program starting characters in the file: No Program ending characters in the file: No

Null modem cable, without handshake

PC, 9pin, DB9M | CNC, 25pin, DB25

Null modem cable, without handshake

PC, 25pin, DB25M | CNC, 25pin, DB25

Fagor 8020 - Machine parameters

Set the following parameters on the machine

P0 (baud rate)	7 (9600)
P1 (data bits)	1 (8 data bits)
P2 (parity)	0 (no parity)
P3 (stop bits)	0 (one stop bit)
P4 (protocol type)	0 (general device)
P5 (Fagor DNC is active)	No
P6 (Debug)	No
P7 (Abort characters)	0
P8 (EOL characters)	0 (LF)
P9 (EOT characters)	0
P10 (Xon and Xoff)	Yes

If you want you can change baud rate in the parameter P0 to:
Baud	Parameter value
1200	4
2400	5
4800	6
9600	7
19200	8
38400	9
57600	10

Set the following parameters on the PC

Serial port tab

Machine name	Fagor 8020
Serial port	COM2 (or any free COM port)
Baud	9600
Data bits	8
Parity	None
Stop bits	1

Data flow control tab

Use DTR	False
Use RTS	False
Require DSR	False
Require CTS	False
Set RTS	False
Set DTR	False
Software flowcontrol	Both
Xon char	#11
Xoff char	#13

Data exchange format tab

Format mode	Uniform
Format parameters	Program start: Program end: Line start: Line end: #0A Skip lines: Ignore characters: No characters for remove Remove blank lines: No Program name prefix: O Program starting characters in the file: No Program ending characters in the file: No

Null modem cable, without handshake

PC, 9pin, DB9M | CNC, 25pin, DB25

Null modem cable, without handshake

PC, 25pin, DB25M | CNC, 25pin, DB25

Fagor 8025 - NC settings

Set the following parameters on the machine

P0 (baud rate)	7 (9600)
P1 (data bits)	1 (8 data bits)
P2 (parity)	0 (no parity)
P3 (stop bits)	0 (one stop bit)
P4 (protocol type)	0 (general device)
P5 (Fagor DNC is active)	No
P6 (Debug)	No
P7 (Abort characters)	0
P8 (EOL characters)	0 (LF)
P9 (EOT characters)	0
P10 (Xon and Xoff)	Yes

If you want you can change baud rate in the parameter P0 to:
Baud	Parameter value
1200	4
2400	5
4800	6
9600	7
19200	8
38400	9
57600	10

Set the following parameters on the PC

Serial port tab

Machine name	Fagor 8025
Serial port	COM2 (or any free COM port)
Baud	9600
Data bits	8
Parity	None
Stop bits	1

Data flow control tab

Use DTR	False
Use RTS	False
Require DSR	False
Require CTS	False
Set RTS	False
Set DTR	False
Software flowcontrol	None
Xon char	#11
Xoff char	#13

Data exchange format tab

Format mode	Uniform
Format parameters	Program start: Program end: Line start: Line end: #0A Skip lines: Ignore characters: No characters for remove Remove blank lines: No Program name prefix: O Program starting characters in the file: No Program ending characters in the file: No

Null modem cable, without handshake

PC, 9pin, DB9M | CNC, 25pin, DB25

Null modem cable, without handshake

PC, 25pin, DB25M | CNC, 25pin, DB25

Fagor 8030 - Machine parameters

Set the following parameters on the machine

P0 (baud rate)	7 (9600)
P1 (data bits)	1 (8 data bits)
P2 (parity)	0 (no parity)
P3 (stop bits)	0 (one stop bit)
P4 (protocol type)	0 (general device)
P5 (Fagor DNC is active)	No
P6 (Debug)	No
P7 (Abort characters)	0
P8 (EOL characters)	0 (LF)
P9 (EOT characters)	0
P10 (Xon and Xoff)	Yes

If you want you can change baud rate in the parameter P0 to:
Baud	Parameter value
1200	4
2400	5
4800	6
9600	7
19200	8
38400	9
57600	10

Set the following parameters on the PC

Serial port tab

Machine name	Fagor 8030
Serial port	COM2 (or any free COM port)
Baud	9600
Data bits	8
Parity	None
Stop bits	1

Data flow control tab

Use DTR	False
Use RTS	False
Require DSR	False
Require CTS	False
Set RTS	False
Set DTR	False
Software flowcontrol	Both
Xon char	#11
Xoff char	#13

Data exchange format tab

Format mode	Uniform
Format parameters	Program start: Program end: Line start: Line end: #0A Skip lines: Ignore characters: No characters for remove Remove blank lines: No Program name prefix: O Program starting characters in the file: No Program ending characters in the file: No

Null modem cable, without handshake

PC, 9pin, DB9M | CNC, 25pin, DB25

Null modem cable, without handshake

PC, 25pin, DB25M | CNC, 25pin, DB25

Fagor 8040/8050 - NC settings

Set the following parameters on the machine

P0 (baud rate)	7 (9600)
P1 (data bits)	1 (8 data bits)
P2 (parity)	0 (no parity)
P3 (stop bits)	0 (one stop bit)
P4 (protocol type)	0 (general device)
P5 (Fagor DNC is active)	No
P6 (Debug)	No
P7 (Abort characters)	0
P8 (EOL characters)	0 (LF)
P9 (EOT characters)	0
P10 (Xon and Xoff)	Yes

If you want you can change baud rate in the parameter P0 to:
Baud	Parameter value
1200	4
2400	5
4800	6
9600	7
19200	8
38400	9
57600	10

Set the following parameters on the PC

Serial port tab

Machine name	Fagor 8040/8050
Serial port	COM2 (or any free COM port)
Baud	9600
Data bits	8
Parity	None
Stop bits	1

Data flow control tab

Use DTR	False
Use RTS	False
Require DSR	False
Require CTS	False
Set RTS	False
Set DTR	False
Software flowcontrol	Both
Xon char	#11
Xoff char	#13

Data exchange format tab

Format mode	Uniform
Format parameters	Program start: Program end: Line start: Line end: #0A Skip lines: Ignore characters: No characters for remove Remove blank lines: No Program name prefix: O Program starting characters in the file: No Program ending characters in the file: No

Null modem cable, without handshake

PC, 9pin, DB9M | CNC, 25pin, DB25

Null modem cable, without handshake

PC, 25pin, DB25M | CNC, 25pin, DB25

Go to Index page
Fadal VMC
Ellison Technologies - Puma VT900
Fanuc 0-P
Fanuc MSC-516

If you connected DNC Precision to another controller that is not on this list, please send us the information so we can add it to the list.