Use different devices for input and output, but with same port number
IO device parameters #1
Parameter
Value
2 (baud rate)
2 (4800)
3 (stop bits)
3 (two stop bits)
4 (parity enabled)
0 (No)
5 (parity)
1 (Even)
6 (data bits)
3 (8 dat bits)
7 (termintator type)
3 (EOR)
11 (handshake)
3 (DC codes)
12 (parity on DC)
1 (Yes)
IO parameters screen #2
Parameter
Value
1 (DC2 and DC4)
1 (DC2 only)
2 (CR)
1 (Yes)
3 (EIA output)
0 (No, ISO)
6 (Parity V)
0 (No)
7 (Timeout)
200 (200 sec)
Set the following parameters on the PC
Serial port tab
Machine name
Mitsubishi - 300 - 500
Serial port
COM2 (or any free COM port)
Baud
4800
Data bits
8
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
False
Require DSR
False
Require CTS
False
Set RTS
False
Set DTR
False
Software flowcontrol
Both
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: Program end: Line start: Line end: #0D#0A Skip lines: Ignore characters: No characters for remove Remove blank lines: No Program name prefix: O Program starting characters in the file: No Program ending characters in the file: No
Use different devices for input and output, but with same port number
IO parameters screen 1/6
9001 (In port #)
2
9002 (In device #)
1
9003 (Out port #)
2
9004 (Out device #)
0
9005 (Tape mode)
2
IO parameters screen 2/6
9101
OUT/IN
9102 (baud rate)
2 (4800)
9103 (stop bits)
1 (one stop bit)
9104 (add parity)
1 (Yes)
9105 (parity)
1 (Even)
9106 (data bits)
2 (7 data bits)
9108 (use DC codes)
3 (yes, DC1 and DC3)
9109 (no parity for DC codes)
1 (Yes)
9112 (CR output)
1 (Yes)
9113 (EIA output)
0 (No)
9114 (Feed chr.)
0 (No)
IO parameters screen 3/6
9201
OUT/IN
9202 (baud rate)
2 (4800)
9203 (stop bits)
1 (one stop bit)
9204 (add parity)
1 (Yes)
9205 (parity)
1 (Even)
9206 (data bits)
2 (7 data bits)
9208 (use DC codes)
3 (yes, DC1 and DC3)
9209 (no parity for DC codes)
1 (Yes)
9212 (CR output)
1 (Yes)
9213 (EIA output)
0 (No)
9214 (Feed chr.)
0 (No)
Set the following parameters on the PC
Serial port tab
Machine name
Mitsubishi - M50
Serial port
COM2 (or any free COM port)
Baud
4800
Data bits
7
Parity
Even
Stop bits
1
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
Both
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: #00#00%%#00#00 Program end: #00#00%%#00#00 Line start: Line end: #0D#0A Skip lines: Ignore characters: No characters for remove Remove blank lines: No Program name prefix: O Program starting characters in the file: No Program ending characters in the file: No
Program start: %% Program end: %% Line start: Line end: #0D#0A Skip lines: Ignore characters: No characters for remove Remove blank lines: No Program name prefix: O Program starting characters in the file: No Program ending characters in the file: No
Use different devices for input and output, but with same port number
IO parameters screen 1/6
9001 (In port #)
2
9002 (In device #)
1
9003 (Out port #)
2
9004 (Out device #)
0
9005 (Tape mode)
2
IO parameters
9101,9201
IN,OUT
9102,9202 (baud rate)
2 (4800)
9103,9203 (stop bits)
1 (one stop bit)
9104,9204 (add parity)
1 (Yes)
9105,9205 (parity)
1 (Even)
9106,9206 (data bits)
2 (7 data bits)
9108,9208 (use DC codes)
3 (yes, DC1 and DC3)
9109,9209 (no parity for DC codes)
1 (Yes)
9112,9212 (CR output)
1 (Yes)
9113,9213 (EIA output)
0 (No)
9114,9214 (Feed chr.)
0 (No)
Set the following parameters on the PC
Serial port tab
Machine name
Mitsubishi - Meldas 60 Series
Serial port
COM2 (or any free COM port)
Baud
4800
Data bits
7
Parity
Even
Stop bits
1
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
Both
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %% Program end: %% Line start: Line end: #0A Skip lines: Ignore characters: No characters for remove Remove blank lines: No Program name prefix: O Program starting characters in the file: No Program ending characters in the file: No
